| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Fix NULL pointer dereference in snd_usb_mixer_controls_badd
In snd_usb_create_streams(), for UAC version 3 devices, the Interface
Association Descriptor (IAD) is retrieved via usb_ifnum_to_if(). If this
call fails, a fallback routine attempts to obtain the IAD from the next
interface and sets a BADD profile. However, snd_usb_mixer_controls_badd()
assumes that the IAD retrieved from usb_ifnum_to_if() is always valid,
without performing a NULL check. This can lead to a NULL pointer
dereference when usb_ifnum_to_if() fails to find the interface descriptor.
This patch adds a NULL pointer check after calling usb_ifnum_to_if() in
snd_usb_mixer_controls_badd() to prevent the dereference.
This issue was discovered by syzkaller, which triggered the bug by sending
a crafted USB device descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: micrel: always set shared->phydev for LAN8814
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix improper check of dentry.stream.valid_size
We found an infinite loop bug in the exFAT file system that can lead to a
Denial-of-Service (DoS) condition. When a dentry in an exFAT filesystem is
malformed, the following system calls — SYS_openat, SYS_ftruncate, and
SYS_pwrite64 — can cause the kernel to hang.
Root cause analysis shows that the size validation code in exfat_find()
does not check whether dentry.stream.valid_size is negative. As a result,
the system calls mentioned above can succeed and eventually trigger the DoS
issue.
This patch adds a check for negative dentry.stream.valid_size to prevent
this vulnerability. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix out of bounds memory read error in symlink repair
xfs/286 produced this report on my test fleet:
==================================================================
BUG: KFENCE: out-of-bounds read in memcpy_orig+0x54/0x110
Out-of-bounds read at 0xffff88843fe9e038 (184B right of kfence-#184):
memcpy_orig+0x54/0x110
xrep_symlink_salvage_inline+0xb3/0xf0 [xfs]
xrep_symlink_salvage+0x100/0x110 [xfs]
xrep_symlink+0x2e/0x80 [xfs]
xrep_attempt+0x61/0x1f0 [xfs]
xfs_scrub_metadata+0x34f/0x5c0 [xfs]
xfs_ioc_scrubv_metadata+0x387/0x560 [xfs]
xfs_file_ioctl+0xe23/0x10e0 [xfs]
__x64_sys_ioctl+0x76/0xc0
do_syscall_64+0x4e/0x1e0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
kfence-#184: 0xffff88843fe9df80-0xffff88843fe9dfea, size=107, cache=kmalloc-128
allocated by task 3470 on cpu 1 at 263329.131592s (192823.508886s ago):
xfs_init_local_fork+0x79/0xe0 [xfs]
xfs_iformat_local+0xa4/0x170 [xfs]
xfs_iformat_data_fork+0x148/0x180 [xfs]
xfs_inode_from_disk+0x2cd/0x480 [xfs]
xfs_iget+0x450/0xd60 [xfs]
xfs_bulkstat_one_int+0x6b/0x510 [xfs]
xfs_bulkstat_iwalk+0x1e/0x30 [xfs]
xfs_iwalk_ag_recs+0xdf/0x150 [xfs]
xfs_iwalk_run_callbacks+0xb9/0x190 [xfs]
xfs_iwalk_ag+0x1dc/0x2f0 [xfs]
xfs_iwalk_args.constprop.0+0x6a/0x120 [xfs]
xfs_iwalk+0xa4/0xd0 [xfs]
xfs_bulkstat+0xfa/0x170 [xfs]
xfs_ioc_fsbulkstat.isra.0+0x13a/0x230 [xfs]
xfs_file_ioctl+0xbf2/0x10e0 [xfs]
__x64_sys_ioctl+0x76/0xc0
do_syscall_64+0x4e/0x1e0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
CPU: 1 UID: 0 PID: 1300113 Comm: xfs_scrub Not tainted 6.18.0-rc4-djwx #rc4 PREEMPT(lazy) 3d744dd94e92690f00a04398d2bd8631dcef1954
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-4.module+el8.8.0+21164+ed375313 04/01/2014
==================================================================
On further analysis, I realized that the second parameter to min() is
not correct. xfs_ifork::if_bytes is the size of the xfs_ifork::if_data
buffer. if_bytes can be smaller than the data fork size because:
(a) the forkoff code tries to keep the data area as large as possible
(b) for symbolic links, if_bytes is the ondisk file size + 1
(c) forkoff is always a multiple of 8.
Case in point: for a single-byte symlink target, forkoff will be
8 but the buffer will only be 2 bytes long.
In other words, the logic here is wrong and we walk off the end of the
incore buffer. Fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: prevent NULL deref in generic_hwtstamp_ioctl_lower()
The ethtool tsconfig Netlink path can trigger a null pointer
dereference. A call chain such as:
tsconfig_prepare_data() ->
dev_get_hwtstamp_phylib() ->
vlan_hwtstamp_get() ->
generic_hwtstamp_get_lower() ->
generic_hwtstamp_ioctl_lower()
results in generic_hwtstamp_ioctl_lower() being called with
kernel_cfg->ifr as NULL.
The generic_hwtstamp_ioctl_lower() function does not expect
a NULL ifr and dereferences it, leading to a system crash.
Fix this by adding a NULL check for kernel_cfg->ifr in
generic_hwtstamp_ioctl_lower(). If ifr is NULL, return -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix scx_enable() crash on helper kthread creation failure
A crash was observed when the sched_ext selftests runner was
terminated with Ctrl+\ while test 15 was running:
NIP [c00000000028fa58] scx_enable.constprop.0+0x358/0x12b0
LR [c00000000028fa2c] scx_enable.constprop.0+0x32c/0x12b0
Call Trace:
scx_enable.constprop.0+0x32c/0x12b0 (unreliable)
bpf_struct_ops_link_create+0x18c/0x22c
__sys_bpf+0x23f8/0x3044
sys_bpf+0x2c/0x6c
system_call_exception+0x124/0x320
system_call_vectored_common+0x15c/0x2ec
kthread_run_worker() returns an ERR_PTR() on failure rather than NULL,
but the current code in scx_alloc_and_add_sched() only checks for a NULL
helper. Incase of failure on SIGQUIT, the error is not handled in
scx_alloc_and_add_sched() and scx_enable() ends up dereferencing an
error pointer.
Error handling is fixed in scx_alloc_and_add_sched() to propagate
PTR_ERR() into ret, so that scx_enable() jumps to the existing error
path, avoiding random dereference on failure. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gud: Fix UBSAN warning
UBSAN complains about invalid value for bool:
[ 101.165172] [drm] Initialized gud 1.0.0 20200422 for 2-3.2:1.0 on minor 1
[ 101.213360] gud 2-3.2:1.0: [drm] fb1: guddrmfb frame buffer device
[ 101.213426] usbcore: registered new interface driver gud
[ 101.989431] ================================================================================
[ 101.989441] UBSAN: invalid-load in linux/include/linux/iosys-map.h:253:9
[ 101.989447] load of value 121 is not a valid value for type '_Bool'
[ 101.989451] CPU: 1 PID: 455 Comm: kworker/1:6 Not tainted 5.18.0-rc5-gud-5.18-rc5 #3
[ 101.989456] Hardware name: Hewlett-Packard HP EliteBook 820 G1/1991, BIOS L71 Ver. 01.44 04/12/2018
[ 101.989459] Workqueue: events_long gud_flush_work [gud]
[ 101.989471] Call Trace:
[ 101.989474] <TASK>
[ 101.989479] dump_stack_lvl+0x49/0x5f
[ 101.989488] dump_stack+0x10/0x12
[ 101.989493] ubsan_epilogue+0x9/0x3b
[ 101.989498] __ubsan_handle_load_invalid_value.cold+0x44/0x49
[ 101.989504] dma_buf_vmap.cold+0x38/0x3d
[ 101.989511] ? find_busiest_group+0x48/0x300
[ 101.989520] drm_gem_shmem_vmap+0x76/0x1b0 [drm_shmem_helper]
[ 101.989528] drm_gem_shmem_object_vmap+0x9/0xb [drm_shmem_helper]
[ 101.989535] drm_gem_vmap+0x26/0x60 [drm]
[ 101.989594] drm_gem_fb_vmap+0x47/0x150 [drm_kms_helper]
[ 101.989630] gud_prep_flush+0xc1/0x710 [gud]
[ 101.989639] ? _raw_spin_lock+0x17/0x40
[ 101.989648] gud_flush_work+0x1e0/0x430 [gud]
[ 101.989653] ? __switch_to+0x11d/0x470
[ 101.989664] process_one_work+0x21f/0x3f0
[ 101.989673] worker_thread+0x200/0x3e0
[ 101.989679] ? rescuer_thread+0x390/0x390
[ 101.989684] kthread+0xfd/0x130
[ 101.989690] ? kthread_complete_and_exit+0x20/0x20
[ 101.989696] ret_from_fork+0x22/0x30
[ 101.989706] </TASK>
[ 101.989708] ================================================================================
The source of this warning is in iosys_map_clear() called from
dma_buf_vmap(). It conditionally sets values based on map->is_iomem. The
iosys_map variables are allocated uninitialized on the stack leading to
->is_iomem having all kinds of values and not only 0/1.
Fix this by zeroing the iosys_map variables. |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
Syzbot reports a memory leak in "dvb_usb_adapter_init()".
The leak is due to not accounting for and freeing current iteration's
adapter->priv in case of an error. Currently if an error occurs,
it will exit before incrementing "num_adapters_initalized",
which is used as a reference counter to free all adap->priv
in "dvb_usb_adapter_exit()". There are multiple error paths that
can exit from before incrementing the counter. Including the
error handling paths for "dvb_usb_adapter_stream_init()",
"dvb_usb_adapter_dvb_init()" and "dvb_usb_adapter_frontend_init()"
within "dvb_usb_adapter_init()".
This means that in case of an error in any of these functions the
current iteration is not accounted for and the current iteration's
adap->priv is not freed.
Fix this by freeing the current iteration's adap->priv in the
"stream_init_err:" label in the error path. The rest of the
(accounted for) adap->priv objects are freed in dvb_usb_adapter_exit()
as expected using the num_adapters_initalized variable.
Syzbot report:
BUG: memory leak
unreferenced object 0xffff8881172f1a00 (size 512):
comm "kworker/0:2", pid 139, jiffies 4294994873 (age 10.960s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff844af012>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:75 [inline]
[<ffffffff844af012>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:184 [inline]
[<ffffffff844af012>] dvb_usb_device_init.cold+0x4e5/0x79e drivers/media/usb/dvb-usb/dvb-usb-init.c:308
[<ffffffff830db21d>] dib0700_probe+0x8d/0x1b0 drivers/media/usb/dvb-usb/dib0700_core.c:883
[<ffffffff82d3fdc7>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752
[<ffffffff8274af6a>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:782
[<ffffffff8274b786>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:899
[<ffffffff82747c87>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff8274b352>] __device_attach+0x122/0x260 drivers/base/dd.c:970
[<ffffffff827498f6>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487
[<ffffffff82745cdb>] device_add+0x5fb/0xdf0 drivers/base/core.c:3405
[<ffffffff82d3d202>] usb_set_configuration+0x8f2/0xb80 drivers/usb/core/message.c:2170
[<ffffffff82d4dbfc>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
[<ffffffff82d3f49c>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to invalidate dcc->f2fs_issue_discard in error path
Syzbot reports a NULL pointer dereference issue as below:
__refcount_add include/linux/refcount.h:193 [inline]
__refcount_inc include/linux/refcount.h:250 [inline]
refcount_inc include/linux/refcount.h:267 [inline]
get_task_struct include/linux/sched/task.h:110 [inline]
kthread_stop+0x34/0x1c0 kernel/kthread.c:703
f2fs_stop_discard_thread+0x3c/0x5c fs/f2fs/segment.c:1638
kill_f2fs_super+0x5c/0x194 fs/f2fs/super.c:4522
deactivate_locked_super+0x70/0xe8 fs/super.c:332
deactivate_super+0xd0/0xd4 fs/super.c:363
cleanup_mnt+0x1f8/0x234 fs/namespace.c:1186
__cleanup_mnt+0x20/0x30 fs/namespace.c:1193
task_work_run+0xc4/0x14c kernel/task_work.c:177
exit_task_work include/linux/task_work.h:38 [inline]
do_exit+0x26c/0xbe0 kernel/exit.c:795
do_group_exit+0x60/0xe8 kernel/exit.c:925
__do_sys_exit_group kernel/exit.c:936 [inline]
__se_sys_exit_group kernel/exit.c:934 [inline]
__wake_up_parent+0x0/0x40 kernel/exit.c:934
__invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:52 [inline]
el0_svc_common+0x138/0x220 arch/arm64/kernel/syscall.c:142
do_el0_svc+0x48/0x164 arch/arm64/kernel/syscall.c:206
el0_svc+0x58/0x150 arch/arm64/kernel/entry-common.c:636
el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:654
el0t_64_sync+0x18c/0x190 arch/arm64/kernel/entry.S:581
The root cause of this issue is in error path of f2fs_start_discard_thread(),
it missed to invalidate dcc->f2fs_issue_discard, later kthread_stop() may
access invalid pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: Fix device use-after-free on unbind
A recent change fixed device reference leaks when looking up drm
platform device driver data during bind() but failed to remove a partial
fix which had been added by commit 80805b62ea5b ("drm/mediatek: Fix
kobject put for component sub-drivers").
This results in a reference imbalance on component bind() failures and
on unbind() which could lead to a user-after-free.
Make sure to only drop the references after retrieving the driver data
by effectively reverting the previous partial fix.
Note that holding a reference to a device does not prevent its driver
data from going away so there is no point in keeping the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: gadget: Use-after-free during failed initialization and exit of cdnsp gadget
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints"). |
| In the Linux kernel, the following vulnerability has been resolved:
9p/trans_fd: p9_fd_request: kick rx thread if EPOLLIN
p9_read_work() doesn't set Rworksched and doesn't do schedule_work(m->rq)
if list_empty(&m->req_list).
However, if the pipe is full, we need to read more data and this used to
work prior to commit aaec5a95d59615 ("pipe_read: don't wake up the writer
if the pipe is still full").
p9_read_work() does p9_fd_read() -> ... -> anon_pipe_read() which (before
the commit above) triggered the unnecessary wakeup. This wakeup calls
p9_pollwake() which kicks p9_poll_workfn() -> p9_poll_mux(), p9_poll_mux()
will notice EPOLLIN and schedule_work(&m->rq).
This no longer happens after the optimization above, change p9_fd_request()
to use p9_poll_mux() instead of only checking for EPOLLOUT. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix NULL pointer dereference in VRAM logic for APU devices
Previously, APU platforms (and other scenarios with uninitialized VRAM managers)
triggered a NULL pointer dereference in `ttm_resource_manager_usage()`. The root
cause is not that the `struct ttm_resource_manager *man` pointer itself is NULL,
but that `man->bdev` (the backing device pointer within the manager) remains
uninitialized (NULL) on APUs—since APUs lack dedicated VRAM and do not fully
set up VRAM manager structures. When `ttm_resource_manager_usage()` attempts to
acquire `man->bdev->lru_lock`, it dereferences the NULL `man->bdev`, leading to
a kernel OOPS.
1. **amdgpu_cs.c**: Extend the existing bandwidth control check in
`amdgpu_cs_get_threshold_for_moves()` to include a check for
`ttm_resource_manager_used()`. If the manager is not used (uninitialized
`bdev`), return 0 for migration thresholds immediately—skipping VRAM-specific
logic that would trigger the NULL dereference.
2. **amdgpu_kms.c**: Update the `AMDGPU_INFO_VRAM_USAGE` ioctl and memory info
reporting to use a conditional: if the manager is used, return the real VRAM
usage; otherwise, return 0. This avoids accessing `man->bdev` when it is
NULL.
3. **amdgpu_virt.c**: Modify the vf2pf (virtual function to physical function)
data write path. Use `ttm_resource_manager_used()` to check validity: if the
manager is usable, calculate `fb_usage` from VRAM usage; otherwise, set
`fb_usage` to 0 (APUs have no discrete framebuffer to report).
This approach is more robust than APU-specific checks because it:
- Works for all scenarios where the VRAM manager is uninitialized (not just APUs),
- Aligns with TTM's design by using its native helper function,
- Preserves correct behavior for discrete GPUs (which have fully initialized
`man->bdev` and pass the `ttm_resource_manager_used()` check).
v4: use ttm_resource_manager_used(&adev->mman.vram_mgr.manager) instead of checking the adev->gmc.is_app_apu flag (Christian) |
| In the Linux kernel, the following vulnerability has been resolved:
net: netpoll: initialize work queue before error checks
Prevent a kernel warning when netconsole setup fails on devices with
IFF_DISABLE_NETPOLL flag. The warning (at kernel/workqueue.c:4242 in
__flush_work) occurs because the cleanup path tries to cancel an
uninitialized work queue.
When __netpoll_setup() encounters a device with IFF_DISABLE_NETPOLL,
it fails early and calls skb_pool_flush() for cleanup. This function
calls cancel_work_sync(&np->refill_wq), but refill_wq hasn't been
initialized yet, triggering the warning.
Move INIT_WORK() to the beginning of __netpoll_setup(), ensuring the
work queue is properly initialized before any potential failure points.
This allows the cleanup path to safely cancel the work queue regardless
of where the setup fails. |
| In the Linux kernel, the following vulnerability has been resolved:
udp_tunnel: use netdev_warn() instead of netdev_WARN()
netdev_WARN() uses WARN/WARN_ON to print a backtrace along with
file and line information. In this case, udp_tunnel_nic_register()
returning an error is just a failed operation, not a kernel bug.
udp_tunnel_nic_register() can fail due to a memory allocation
failure (kzalloc() or udp_tunnel_nic_alloc()).
This is a normal runtime error and not a kernel bug.
Replace netdev_WARN() with netdev_warn() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost: vringh: Fix copy_to_iter return value check
The return value of copy_to_iter can't be negative, check whether the
copied length is equal to the requested length instead of checking for
negative values. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda: cs35l41: Fix NULL pointer dereference in cs35l41_hda_read_acpi()
The acpi_get_first_physical_node() function can return NULL, in which
case the get_device() function also returns NULL, but this value is
then dereferenced without checking,so add a check to prevent a crash.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl818x: Fix potential memory leaks in rtl8180_init_rx_ring()
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free. |
| In the Linux kernel, the following vulnerability has been resolved:
smack: fix bug: unprivileged task can create labels
If an unprivileged task is allowed to relabel itself
(/smack/relabel-self is not empty),
it can freely create new labels by writing their
names into own /proc/PID/attr/smack/current
This occurs because do_setattr() imports
the provided label in advance,
before checking "relabel-self" list.
This change ensures that the "relabel-self" list
is checked before importing the label. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: starfive - Correctly handle return of sg_nents_for_len
The return value of sg_nents_for_len was assigned to an unsigned long
in starfive_hash_digest, causing negative error codes to be converted
to large positive integers.
Add error checking for sg_nents_for_len and return immediately on
failure to prevent potential buffer overflows. |