| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix mmap write lock not release
If mmap write lock is taken while draining retry fault, mmap write lock
is not released because svm_range_restore_pages calls mmap_read_unlock
then returns. This causes deadlock and system hangs later because mmap
read or write lock cannot be taken.
Downgrade mmap write lock to read lock if draining retry fault fix this
bug. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix workqueue leak on bind errors
Make sure to destroy the workqueue also in case of early errors during
bind (e.g. a subcomponent failing to bind).
Since commit c3b790ea07a1 ("drm: Manage drm_mode_config_init with
drmm_") the mode config will be freed when the drm device is released
also when using the legacy interface, but add an explicit cleanup for
consistency and to facilitate backporting.
Patchwork: https://patchwork.freedesktop.org/patch/525093/ |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: report devlink_port_type_warn source device
devlink_port_type_warn is scheduled for port devlink and warning
when the port type is not set. But from this warning it is not easy
found out which device (driver) has no devlink port set.
[ 3709.975552] Type was not set for devlink port.
[ 3709.975579] WARNING: CPU: 1 PID: 13092 at net/devlink/leftover.c:6775 devlink_port_type_warn+0x11/0x20
[ 3709.993967] Modules linked in: openvswitch nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nfnetlink bluetooth rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs vhost_net vhost vhost_iotlb tap tun bridge stp llc qrtr intel_rapl_msr intel_rapl_common i10nm_edac nfit libnvdimm x86_pkg_temp_thermal mlx5_ib intel_powerclamp coretemp dell_wmi ledtrig_audio sparse_keymap ipmi_ssif kvm_intel ib_uverbs rfkill ib_core video kvm iTCO_wdt acpi_ipmi intel_vsec irqbypass ipmi_si iTCO_vendor_support dcdbas ipmi_devintf mei_me ipmi_msghandler rapl mei intel_cstate isst_if_mmio isst_if_mbox_pci dell_smbios intel_uncore isst_if_common i2c_i801 dell_wmi_descriptor wmi_bmof i2c_smbus intel_pch_thermal pcspkr acpi_power_meter xfs libcrc32c sd_mod sg nvme_tcp mgag200 i2c_algo_bit nvme_fabrics drm_shmem_helper drm_kms_helper nvme syscopyarea ahci sysfillrect sysimgblt nvme_core fb_sys_fops crct10dif_pclmul libahci mlx5_core sfc crc32_pclmul nvme_common drm
[ 3709.994030] crc32c_intel mtd t10_pi mlxfw libata tg3 mdio megaraid_sas psample ghash_clmulni_intel pci_hyperv_intf wmi dm_multipath sunrpc dm_mirror dm_region_hash dm_log dm_mod be2iscsi bnx2i cnic uio cxgb4i cxgb4 tls libcxgbi libcxgb qla4xxx iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi fuse
[ 3710.108431] CPU: 1 PID: 13092 Comm: kworker/1:1 Kdump: loaded Not tainted 5.14.0-319.el9.x86_64 #1
[ 3710.108435] Hardware name: Dell Inc. PowerEdge R750/0PJ80M, BIOS 1.8.2 09/14/2022
[ 3710.108437] Workqueue: events devlink_port_type_warn
[ 3710.108440] RIP: 0010:devlink_port_type_warn+0x11/0x20
[ 3710.108443] Code: 84 76 fe ff ff 48 c7 03 20 0e 1a ad 31 c0 e9 96 fd ff ff 66 0f 1f 44 00 00 0f 1f 44 00 00 48 c7 c7 18 24 4e ad e8 ef 71 62 ff <0f> 0b c3 cc cc cc cc 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f6 87
[ 3710.108445] RSP: 0018:ff3b6d2e8b3c7e90 EFLAGS: 00010282
[ 3710.108447] RAX: 0000000000000000 RBX: ff366d6580127080 RCX: 0000000000000027
[ 3710.108448] RDX: 0000000000000027 RSI: 00000000ffff86de RDI: ff366d753f41f8c8
[ 3710.108449] RBP: ff366d658ff5a0c0 R08: ff366d753f41f8c0 R09: ff3b6d2e8b3c7e18
[ 3710.108450] R10: 0000000000000001 R11: 0000000000000023 R12: ff366d753f430600
[ 3710.108451] R13: ff366d753f436900 R14: 0000000000000000 R15: ff366d753f436905
[ 3710.108452] FS: 0000000000000000(0000) GS:ff366d753f400000(0000) knlGS:0000000000000000
[ 3710.108453] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3710.108454] CR2: 00007f1c57bc74e0 CR3: 000000111d26a001 CR4: 0000000000773ee0
[ 3710.108456] PKRU: 55555554
[ 3710.108457] Call Trace:
[ 3710.108458] <TASK>
[ 3710.108459] process_one_work+0x1e2/0x3b0
[ 3710.108466] ? rescuer_thread+0x390/0x390
[ 3710.108468] worker_thread+0x50/0x3a0
[ 3710.108471] ? rescuer_thread+0x390/0x390
[ 3710.108473] kthread+0xdd/0x100
[ 3710.108477] ? kthread_complete_and_exit+0x20/0x20
[ 3710.108479] ret_from_fork+0x1f/0x30
[ 3710.108485] </TASK>
[ 3710.108486] ---[ end trace 1b4b23cd0c65d6a0 ]---
After patch:
[ 402.473064] ice 0000:41:00.0: Type was not set for devlink port.
[ 402.473064] ice 0000:41:00.1: Type was not set for devlink port. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ina2xx: avoid NULL pointer dereference on OF device match
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
power-sensor@40 {
compatible = "ti,ina232", "ti,ina231";
...
};
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table. |
| In the Linux kernel, the following vulnerability has been resolved:
ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
Wear-leveling entry could be freed in error path, which may be accessed
again in eraseblk_count_seq_show(), for example:
__erase_worker eraseblk_count_seq_show
wl = ubi->lookuptbl[*block_number]
if (wl)
wl_entry_destroy
ubi->lookuptbl[e->pnum] = NULL
kmem_cache_free(ubi_wl_entry_slab, e)
erase_count = wl->ec // UAF!
Wear-leveling entry updating/accessing in ubi->lookuptbl should be
protected by ubi->wl_lock, fix it by adding ubi->wl_lock to serialize
wl entry accessing between wl_entry_destroy() and
eraseblk_count_seq_show().
Fetch a reproducer in [Link]. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd720
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour. |
| In the Linux kernel, the following vulnerability has been resolved:
loop: loop_set_status_from_info() check before assignment
In loop_set_status_from_info(), lo->lo_offset and lo->lo_sizelimit should
be checked before reassignment, because if an overflow error occurs, the
original correct value will be changed to the wrong value, and it will not
be changed back.
More, the original patch did not solve the problem, the value was set and
ioctl returned an error, but the subsequent io used the value in the loop
driver, which still caused an alarm:
loop_handle_cmd
do_req_filebacked
loff_t pos = ((loff_t) blk_rq_pos(rq) << 9) + lo->lo_offset;
lo_rw_aio
cmd->iocb.ki_pos = pos |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix dropping valid root bus resources with .end = zero
On r8a7791/koelsch:
kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xc3a34e00 (size 64):
comm "swapper/0", pid 1, jiffies 4294937460 (age 199.080s)
hex dump (first 32 bytes):
b4 5d 81 f0 b4 5d 81 f0 c0 b0 a2 c3 00 00 00 00 .]...]..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fe3aa979>] __kmalloc+0xf0/0x140
[<34bd6bc0>] resource_list_create_entry+0x18/0x38
[<767046bc>] pci_add_resource_offset+0x20/0x68
[<b3f3edf2>] devm_of_pci_get_host_bridge_resources.constprop.0+0xb0/0x390
When coalescing two resources for a contiguous aperture, the second
resource is enlarged to cover the full contiguous range, while the first
resource is marked invalid. This invalidation is done by clearing the
flags, start, and end members.
When adding the initial resources to the bus later, invalid resources are
skipped. Unfortunately, the check for an invalid resource considers only
the end member, causing false positives.
E.g. on r8a7791/koelsch, root bus resource 0 ("bus 00") is skipped, and no
longer registered with pci_bus_insert_busn_res() (causing the memory leak),
nor printed:
pci-rcar-gen2 ee090000.pci: host bridge /soc/pci@ee090000 ranges:
pci-rcar-gen2 ee090000.pci: MEM 0x00ee080000..0x00ee08ffff -> 0x00ee080000
pci-rcar-gen2 ee090000.pci: PCI: revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
-pci_bus 0000:00: root bus resource [bus 00]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee08ffff]
Fix this by only skipping resources where all of the flags, start, and end
members are zero. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix rbtree traversal bug in ext4_mb_use_preallocated
During allocations, while looking for preallocations(PA) in the per
inode rbtree, we can't do a direct traversal of the tree because
ext4_mb_discard_group_preallocation() can paralelly mark the pa deleted
and that can cause direct traversal to skip some entries. This was
leading to a BUG_ON() being hit [1] when we missed a PA that could satisfy
our request and ultimately tried to create a new PA that would overlap
with the missed one.
To makes sure we handle that case while still keeping the performance of
the rbtree, we make use of the fact that the only pa that could possibly
overlap the original goal start is the one that satisfies the below
conditions:
1. It must have it's logical start immediately to the left of
(ie less than) original logical start.
2. It must not be deleted
To find this pa we use the following traversal method:
1. Descend into the rbtree normally to find the immediate neighboring
PA. Here we keep descending irrespective of if the PA is deleted or if
it overlaps with our request etc. The goal is to find an immediately
adjacent PA.
2. If the found PA is on right of original goal, use rb_prev() to find
the left adjacent PA.
3. Check if this PA is deleted and keep moving left with rb_prev() until
a non deleted PA is found.
4. This is the PA we are looking for. Now we can check if it can satisfy
the original request and proceed accordingly.
This approach also takes care of having deleted PAs in the tree.
(While we are at it, also fix a possible overflow bug in calculating the
end of a PA)
[1] https://lore.kernel.org/linux-ext4/CA+G9fYv2FRpLqBZf34ZinR8bU2_ZRAUOjKAD3+tKRFaEQHtt8Q@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Cap MSIX used to online CPUs + 1
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
WARNING: CPU: 7 PID: 23655 at include/linux/cpumask.h:106 irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
RIP: 0010:irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
Call Trace:
irdma_rt_init_hw+0xa62/0x1290 [irdma]
? irdma_alloc_local_mac_entry+0x1a0/0x1a0 [irdma]
? __is_kernel_percpu_address+0x63/0x310
? rcu_read_lock_held_common+0xe/0xb0
? irdma_lan_unregister_qset+0x280/0x280 [irdma]
? irdma_request_reset+0x80/0x80 [irdma]
? ice_get_qos_params+0x84/0x390 [ice]
irdma_probe+0xa40/0xfc0 [irdma]
? rcu_read_lock_bh_held+0xd0/0xd0
? irdma_remove+0x140/0x140 [irdma]
? rcu_read_lock_sched_held+0x62/0xe0
? down_write+0x187/0x3d0
? auxiliary_match_id+0xf0/0x1a0
? irdma_remove+0x140/0x140 [irdma]
auxiliary_bus_probe+0xa6/0x100
__driver_probe_device+0x4a4/0xd50
? __device_attach_driver+0x2c0/0x2c0
driver_probe_device+0x4a/0x110
__driver_attach+0x1aa/0x350
bus_for_each_dev+0x11d/0x1b0
? subsys_dev_iter_init+0xe0/0xe0
bus_add_driver+0x3b1/0x610
driver_register+0x18e/0x410
? 0xffffffffc0b88000
irdma_init_module+0x50/0xaa [irdma]
do_one_initcall+0x103/0x5f0
? perf_trace_initcall_level+0x420/0x420
? do_init_module+0x4e/0x700
? __kasan_kmalloc+0x7d/0xa0
? kmem_cache_alloc_trace+0x188/0x2b0
? kasan_unpoison+0x21/0x50
do_init_module+0x1d1/0x700
load_module+0x3867/0x5260
? layout_and_allocate+0x3990/0x3990
? rcu_read_lock_held_common+0xe/0xb0
? rcu_read_lock_sched_held+0x62/0xe0
? rcu_read_lock_bh_held+0xd0/0xd0
? __vmalloc_node_range+0x46b/0x890
? lock_release+0x5c8/0xba0
? alloc_vm_area+0x120/0x120
? selinux_kernel_module_from_file+0x2a5/0x300
? __inode_security_revalidate+0xf0/0xf0
? __do_sys_init_module+0x1db/0x260
__do_sys_init_module+0x1db/0x260
? load_module+0x5260/0x5260
? do_syscall_64+0x22/0x450
do_syscall_64+0xa5/0x450
entry_SYSCALL_64_after_hwframe+0x66/0xdb |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: api - Use work queue in crypto_destroy_instance
The function crypto_drop_spawn expects to be called in process
context. However, when an instance is unregistered while it still
has active users, the last user may cause the instance to be freed
in atomic context.
Fix this by delaying the freeing to a work queue. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix information leak in f2fs_move_inline_dirents()
When converting an inline directory to a regular one, f2fs is leaking
uninitialized memory to disk because it doesn't initialize the entire
directory block. Fix this by zero-initializing the block.
This bug was introduced by commit 4ec17d688d74 ("f2fs: avoid unneeded
initializing when converting inline dentry"), which didn't consider the
security implications of leaking uninitialized memory to disk.
This was found by running xfstest generic/435 on a KMSAN-enabled kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
perf tool x86: Fix perf_env memory leak
Found by leak sanitizer:
```
==1632594==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 21 byte(s) in 1 object(s) allocated from:
#0 0x7f2953a7077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439
#1 0x556701d6fbbf in perf_env__read_cpuid util/env.c:369
#2 0x556701d70589 in perf_env__cpuid util/env.c:465
#3 0x55670204bba2 in x86__is_amd_cpu arch/x86/util/env.c:14
#4 0x5567020487a2 in arch__post_evsel_config arch/x86/util/evsel.c:83
#5 0x556701d8f78b in evsel__config util/evsel.c:1366
#6 0x556701ef5872 in evlist__config util/record.c:108
#7 0x556701cd6bcd in test__PERF_RECORD tests/perf-record.c:112
#8 0x556701cacd07 in run_test tests/builtin-test.c:236
#9 0x556701cacfac in test_and_print tests/builtin-test.c:265
#10 0x556701cadddb in __cmd_test tests/builtin-test.c:402
#11 0x556701caf2aa in cmd_test tests/builtin-test.c:559
#12 0x556701d3b557 in run_builtin tools/perf/perf.c:323
#13 0x556701d3bac8 in handle_internal_command tools/perf/perf.c:377
#14 0x556701d3be90 in run_argv tools/perf/perf.c:421
#15 0x556701d3c3f8 in main tools/perf/perf.c:537
#16 0x7f2952a46189 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58
SUMMARY: AddressSanitizer: 21 byte(s) leaked in 1 allocation(s).
``` |
| In the Linux kernel, the following vulnerability has been resolved:
md: fix warning for holder mismatch from export_rdev()
Commit a1d767191096 ("md: use mddev->external to select holder in
export_rdev()") fix the problem that 'claim_rdev' is used for
blkdev_get_by_dev() while 'rdev' is used for blkdev_put().
However, if mddev->external is changed from 0 to 1, then 'rdev' is used
for blkdev_get_by_dev() while 'claim_rdev' is used for blkdev_put(). And
this problem can be reporduced reliably by following:
New file: mdadm/tests/23rdev-lifetime
devname=${dev0##*/}
devt=`cat /sys/block/$devname/dev`
pid=""
runtime=2
clean_up_test() {
pill -9 $pid
echo clear > /sys/block/md0/md/array_state
}
trap 'clean_up_test' EXIT
add_by_sysfs() {
while true; do
echo $devt > /sys/block/md0/md/new_dev
done
}
remove_by_sysfs(){
while true; do
echo remove > /sys/block/md0/md/dev-${devname}/state
done
}
echo md0 > /sys/module/md_mod/parameters/new_array || die "create md0 failed"
add_by_sysfs &
pid="$pid $!"
remove_by_sysfs &
pid="$pid $!"
sleep $runtime
exit 0
Test cmd:
./test --save-logs --logdir=/tmp/ --keep-going --dev=loop --tests=23rdev-lifetime
Test result:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 960 at block/bdev.c:618 blkdev_put+0x27c/0x330
Modules linked in: multipath md_mod loop
CPU: 0 PID: 960 Comm: test Not tainted 6.5.0-rc2-00121-g01e55c376936-dirty #50
RIP: 0010:blkdev_put+0x27c/0x330
Call Trace:
<TASK>
export_rdev.isra.23+0x50/0xa0 [md_mod]
mddev_unlock+0x19d/0x300 [md_mod]
rdev_attr_store+0xec/0x190 [md_mod]
sysfs_kf_write+0x52/0x70
kernfs_fop_write_iter+0x19a/0x2a0
vfs_write+0x3b5/0x770
ksys_write+0x74/0x150
__x64_sys_write+0x22/0x30
do_syscall_64+0x40/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fix the problem by recording if 'rdev' is used as holder. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
tuning_ctl_set() might have buffer overrun at (X) if it didn't break
from loop by matching (A).
static int tuning_ctl_set(...)
{
for (i = 0; i < TUNING_CTLS_COUNT; i++)
(A) if (nid == ca0132_tuning_ctls[i].nid)
break;
snd_hda_power_up(...);
(X) dspio_set_param(..., ca0132_tuning_ctls[i].mid, ...);
snd_hda_power_down(...); ^
return 1;
}
We will get below error by cppcheck
sound/pci/hda/patch_ca0132.c:4229:2: note: After for loop, i has value 12
for (i = 0; i < TUNING_CTLS_COUNT; i++)
^
sound/pci/hda/patch_ca0132.c:4234:43: note: Array index out of bounds
dspio_set_param(codec, ca0132_tuning_ctls[i].mid, 0x20,
^
This patch cares non match case. |
| In the Linux kernel, the following vulnerability has been resolved:
dccp: Fix out of bounds access in DCCP error handler
There was a previous attempt to fix an out-of-bounds access in the DCCP
error handlers, but that fix assumed that the error handlers only want
to access the first 8 bytes of the DCCP header. Actually, they also look
at the DCCP sequence number, which is stored beyond 8 bytes, so an
explicit pskb_may_pull() is required. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: fix FCLK pstate change underflow
[Why]
Currently we set FCLK p-state change
watermark calculated based on dummy
p-state latency when UCLK p-state is
not supported
[How]
Calculate FCLK p-state change watermark
based on on FCLK pstate change latency
in case UCLK p-state is not supported |
| An attacker can obtain server information using Path Traversal vulnerability to conduct SQL Injection, which possibly exploits Unrestricted Upload of File with Dangerous Type vulnerability in MarkAny SafePC Enterprise on Windows, Linux.This issue affects SafePC Enterprise: V7.0.* (V7.0.YYYY.MM.DD) before V7.0.1, and V5.*.*. |
| In the Linux kernel, the following vulnerability has been resolved:
uio: uio_dmem_genirq: Fix missing unlock in irq configuration
Commit b74351287d4b ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
root@localhost:~# printf '\x00\x00\x00\x00' > /dev/uio0
root@localhost:~# printf '\x00\x00\x00\x00' > /dev/uio0
root@localhost:~# [ 14.851538] BUG: scheduling while atomic: bash/223/0x00000002
[ 14.851991] Modules linked in: uio_dmem_genirq uio myfpga(OE) bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper drm snd_pcm ppdev joydev psmouse snd_timer snd e1000fb_sys_fops syscopyarea parport sysfillrect soundcore sysimgblt input_leds pcspkr i2c_piix4 serio_raw floppy evbug qemu_fw_cfg mac_hid pata_acpi ip_tables x_tables autofs4 [last unloaded: parport_pc]
[ 14.854206] CPU: 0 PID: 223 Comm: bash Tainted: G OE 6.0.0-rc7 #21
[ 14.854786] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
[ 14.855664] Call Trace:
[ 14.855861] <TASK>
[ 14.856025] dump_stack_lvl+0x4d/0x67
[ 14.856325] dump_stack+0x14/0x1a
[ 14.856583] __schedule_bug.cold+0x4b/0x5c
[ 14.856915] __schedule+0xe81/0x13d0
[ 14.857199] ? idr_find+0x13/0x20
[ 14.857456] ? get_work_pool+0x2d/0x50
[ 14.857756] ? __flush_work+0x233/0x280
[ 14.858068] ? __schedule+0xa95/0x13d0
[ 14.858307] ? idr_find+0x13/0x20
[ 14.858519] ? get_work_pool+0x2d/0x50
[ 14.858798] schedule+0x6c/0x100
[ 14.859009] schedule_hrtimeout_range_clock+0xff/0x110
[ 14.859335] ? tty_write_room+0x1f/0x30
[ 14.859598] ? n_tty_poll+0x1ec/0x220
[ 14.859830] ? tty_ldisc_deref+0x1a/0x20
[ 14.860090] schedule_hrtimeout_range+0x17/0x20
[ 14.860373] do_select+0x596/0x840
[ 14.860627] ? __kernel_text_address+0x16/0x50
[ 14.860954] ? poll_freewait+0xb0/0xb0
[ 14.861235] ? poll_freewait+0xb0/0xb0
[ 14.861517] ? rpm_resume+0x49d/0x780
[ 14.861798] ? common_interrupt+0x59/0xa0
[ 14.862127] ? asm_common_interrupt+0x2b/0x40
[ 14.862511] ? __uart_start.isra.0+0x61/0x70
[ 14.862902] ? __check_object_size+0x61/0x280
[ 14.863255] core_sys_select+0x1c6/0x400
[ 14.863575] ? vfs_write+0x1c9/0x3d0
[ 14.863853] ? vfs_write+0x1c9/0x3d0
[ 14.864121] ? _copy_from_user+0x45/0x70
[ 14.864526] do_pselect.constprop.0+0xb3/0xf0
[ 14.864893] ? do_syscall_64+0x6d/0x90
[ 14.865228] ? do_syscall_64+0x6d/0x90
[ 14.865556] __x64_sys_pselect6+0x76/0xa0
[ 14.865906] do_syscall_64+0x60/0x90
[ 14.866214] ? syscall_exit_to_user_mode+0x2a/0x50
[ 14.866640] ? do_syscall_64+0x6d/0x90
[ 14.866972] ? do_syscall_64+0x6d/0x90
[ 14.867286] ? do_syscall_64+0x6d/0x90
[ 14.867626] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...] stripped
[ 14.872959] </TASK>
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 34cb27528398 ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-whil
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
pm_runtime_get_sync() will increment pm usage counter.
Forgetting to putting operation will result in reference leak.
Add missing pm_runtime_put_sync in some error paths. |
