| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Fix snp_filter_reserved_mem_regions() off-by-one
Sashiko notes:
> regarding the bounds check in snp_filter_reserved_mem_regions()
> called via walk_iomem_res_desc(): does the check
> if ((range_list->num_elements * 16 + 8) > PAGE_SIZE)
> allow an off-by-one heap buffer overflow?
>
> If range_list->num_elements is 255, 255 * 16 + 8 = 4088, which is <= 4096.
> Writing range->base (8 bytes) fills 4088-4095, but writing range->page_count
> (4 bytes) would write to 4096-4099, overflowing the kzalloc-allocated
> PAGE_SIZE buffer.
Fix this by accounting for the entry about to be written to, in addition to
the entries that are already allocated. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix UMR XLT cleanup on ODP populate failure
mlx5r_umr_update_xlt() allocates and DMA maps an XLT buffer with
mlx5r_umr_create_xlt(). The buffer is released by the common cleanup path
through mlx5r_umr_unmap_free_xlt().
After mlx5_odp_populate_xlt() became fallible, its error path returned
directly and skipped that cleanup. This leaks the XLT DMA mapping and
buffer. If the emergency XLT page was used, it also leaves
xlt_emergency_page_mutex locked.
Break out of the loop so execution falls through the existing cleanup path. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix out-of-bounds write in irdma_copy_user_pgaddrs
The irdma_copy_user_pgaddrs function loops through all of the umem DMA
blocks to populate the PBLEs and will stop when either the last DMA
block is reached or palloc->total_cnt is reached. The issue is that
the logic for checking palloc->total_cnt would only work for non-zero
values.
When irdma_setup_pbles is called with lvl==0, it
calls irdma_copy_user_pgaddrs with palloc->total_cnt==0, which means
the only way to break out of the loop is to reach the last umem DMA
block, which means it could end up going beyond the fixed size of 4
iwmr->pgaddrmem array that is used in the lvl==0 case.
In the case of QP/CQ/SRQ rings, the value of lvl is determined by a
separate input (for example, req.cq_pages in the case of a CQ). So,
we must perform explicit checking to ensure we don't overflow the
pgaddrmem array if the user provides a umem that consists of more
blocks than their provided req.cq_pages. |
| Dragonfly through 2.0.2 contains an unbounded memory allocation vulnerability that allows unauthenticated clients to exhaust memory by passing a negative COUNT to HRANDFIELD, ZRANDMEMBER or SRANDMEMBER. Attackers can send a single command against a one-element key with a huge negative COUNT to trigger the OOM killer, terminating the instance for all clients. |
| lichess.org is the forever free, adless and open source chess server. Prior to commit c54596c9e1569d378fe20f80d4c790c6fdee54c4, a user who can add a chapter to a study can place attacker-controlled text in the PGN Annotator tag, which becomes Comment.Author.External and is returned verbatim by authorText. When a study node has at least two comments, ui/analyse/src/treeView/inlineView.ts interpolates that author string into HTML passed to the innerHTML hook without escaping it. Opening the affected study can therefore render stored attacker-controlled HTML and CSS for other viewers, including navigation to an attacker-controlled site, content spoofing, and CSS-based data exposure, although the site's content security policy blocks injected JavaScript. This vulnerability is fixed by commit c54596c9e1569d378fe20f80d4c790c6fdee54c4. |
| Allocation of resources without limits or throttling in .NET allows an unauthorized attacker to deny service over a network. |
| Agnaistic agnai through 1.0.555 contains a hard-coded credentials vulnerability in self-host.docker-compose.yml, which sets a fixed admin password and public JWT secret. Unauthenticated attackers can log in as admin or sign their own JWT with admin: true to impersonate users, reset passwords, and change server configuration. |
| libmspack through 0.11alpha contains an uninitialized pointer free vulnerability in kwajd_open() in mspack/kwajd.c that frees unzeroed filename and extra pointers on header read errors. Attackers can supply a truncated, empty, or wrong-signature KWAJ file to crash the process or obtain an arbitrary-free memory corruption primitive. |
| open-computer-use through commit 610bac8 contains a stored cross-site scripting vulnerability in Logger.write_log_file in os_computer_use/logging.py, which writes transcript text into log.html without HTML escaping. Attackers controlling sandbox content, such as web pages or files appearing in run_command output, can inject script that runs when operators open the log, exfiltrating transcript contents. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-multipath: fix flex array size in struct nvme_ns_head
struct nvme_ns_head contains a flexible array member, current_path[],
which is indexed using the NUMA node ID:
head->current_path[numa_node_id()]
The structure is currently allocated as:
size = sizeof(struct nvme_ns_head) +
(num_possible_nodes() * sizeof(struct nvme_ns *));
head = kzalloc(size, GFP_KERNEL);
This allocation assumes that NUMA node IDs are sequential and densely
packed from 0 .. num_possible_nodes() - 1. While this assumption holds
on many systems, it is not always true on some architectures such as
powerpc.
On some powerpc systems, NUMA node IDs can be sparse. For example:
NUMA:
NUMA node(s): 6
NUMA node0 CPU(s): 80-159
NUMA node8 CPU(s): 0-79
NUMA node252 CPU(s):
NUMA node253 CPU(s):
NUMA node254 CPU(s):
NUMA node255 CPU(s):
That is, the possible/online NUMA node IDs are: 0, 8, 252, 253, 254, 255
In this case: num_possible_nodes() = 6
So memory is allocated for only 6 entries in current_path[]. However,
the array is later indexed using the actual NUMA node ID. As a result,
accesses such as:
head->current_path[8] or
head->current_path[252]
goes out of bounds, leading to the following KASAN splat:
==================================================================
BUG: KASAN: slab-out-of-bounds in nvme_mpath_revalidate_paths+0x22c/0x290 [nvme_core]
Write of size 8 at addr c00020003bda35b8 by task kworker/u641:2/1997
CPU: 1 UID: 0 PID: 1997 Comm: kworker/u641:2 Not tainted 7.1.0-rc5-dirty #14 PREEMPT(lazy)
Hardware name: 8335-GTH POWER9 0x4e1202 opal:skiboot-v6.5.3-35-g1851b2a06 PowerNV
Workqueue: async async_run_entry_fn
Call Trace:
[c000200037fa7510] [c0000000021c23d4] dump_stack_lvl+0x88/0xdc (unreliable)
[c000200037fa7540] [c0000000009fda90] print_report+0x22c/0x67c
[c000200037fa7630] [c0000000009fd508] kasan_report+0x108/0x220
[c000200037fa7740] [c0000000009fff48] __asan_store8+0xe8/0x120
[c000200037fa7760] [c008000018e76474] nvme_mpath_revalidate_paths+0x22c/0x290 [nvme_core]
[c000200037fa7800] [c008000018e6556c] nvme_update_ns_info+0x4a4/0x5e0 [nvme_core]
[c000200037fa7a50] [c008000018e66270] nvme_alloc_ns+0x6d8/0x1a70 [nvme_core]
[c000200037fa7c20] [c008000018e679fc] nvme_scan_ns+0x3f4/0x630 [nvme_core]
[c000200037fa7d10] [c00000000031f22c] async_run_entry_fn+0x9c/0x3a0
[c000200037fa7db0] [c0000000002fa544] process_one_work+0x414/0xa10
[c000200037fa7ec0] [c0000000002fbf00] worker_thread+0x320/0x640
[c000200037fa7f80] [c00000000030d0f8] kthread+0x278/0x290
[c000200037fa7fe0] [c00000000000ded8] start_kernel_thread+0x14/0x18
Allocated by task 1997 on cpu 1 at 35.928317s:
The buggy address belongs to the object at c00020003bda3000
which belongs to the cache kmalloc-rnd-15-2k of size 2048
The buggy address is located 16 bytes to the right of
allocated 1448-byte region [c00020003bda3000, c00020003bda35a8)
The buggy address belongs to the physical page:
Memory state around the buggy address:
c00020003bda3480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c00020003bda3500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>c00020003bda3580: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
^
c00020003bda3600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
c00020003bda3680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fix this by allocating the flexible array using nr_node_ids instead
of num_possible_nodes(). Since nr_node_ids represents the maximum
possible NUMA node IDs, indexing current_path[] using numa_node_id()
becomes safe even on systems with sparse node IDs. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: reset read_slot when reusing r10bio for discard
put_all_bios() always drops devs[i].bio, but it only drops
devs[i].repl_bio when r10_bio->read_slot < 0. If discard reuses an
r10bio that was previously used for a read, read_slot can still be
non-negative, and discard cleanup can skip bio_put() on repl_bio.
Reset read_slot to -1 when preparing an r10bio for discard so the
replacement bio is always released correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: reject FITRIM ranges shorter than a cluster
ocfs2_trim_mainbm() trims the global bitmap in cluster units, but its
too-short range validation only checks sb->s_blocksize.
On filesystems with a cluster size larger than the block size, a FITRIM
range that is at least one block but shorter than one cluster is accepted
and shifted down to len == 0. The later start + len - 1 and len -= ...
arithmetic then underflows and can drive trimming past the requested
range.
Reject ranges shorter than s_clustersize instead. That preserves the
existing -EINVAL behavior for requests that cannot discard even one
allocation unit and keeps zero-cluster trims out of the group walk. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: Fix possible token leak in mt7996_tx_prepare_skb()
If link_conf or link_sta lookup fails in mt7996_tx_prepare_skb routine,
mt7996 driver leaks an already allocated tx token. Fix the issue
releasing the token in case of error. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Handle layout stid in nfsd4_drop_revoked_stid()
nfsd4_drop_revoked_stid() has no SC_TYPE_LAYOUT case, so when a
client sends FREE_STATEID for an admin-revoked layout stid, the
default branch releases cl_lock and returns without unhashing or
releasing the stid. The stid remains in the IDR and on the
per-client list until the client is destroyed.
Remove the layout stid from the per-client list and call
nfs4_put_stid() to drop the creation reference. When the
refcount reaches zero, nfsd4_free_layout_stateid() handles the
remaining cleanup: cancelling the fence worker, removing from
the per-file list, and freeing the slab object. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Cancel special fields on map value recycle
Map update and delete paths currently call bpf_obj_free_fields() when a
value is being replaced or recycled. That makes field destruction depend
on the context of the update/delete operation. For tracing programs this
can include NMI context, where referenced kptr destructors, uptr
unpinning, and graph root destruction are not generally safe.
Introduce bpf_obj_cancel_fields() for the reusable-value path. It only
performs NMI-safe cleanup for timer, workqueue, and task_work fields.
Fields that need full destruction are left attached to the recycled value
and are destroyed by the final cleanup path instead.
Switch array and hashtab update/delete/recycle paths to this cancel
helper. Keep bpf_obj_free_fields() for final map destruction and for
bpf_mem_alloc destructors. Preallocated hashtabs do not have allocator
destructors, so teardown continues to walk the normal and extra elements
and fully destroy their fields.
This deliberately relaxes the eager-free semantics of map update/delete
for special fields. Programs that relied on a recycled map slot becoming
empty immediately after update/delete were relying on behavior that
cannot be implemented safely from every BPF execution context without
offloading arbitrary destructors.
There is a chance this change breaks programs making assumptions
regarding the eager freeing of fields. If so, we can relax semantics to
cancellation only when irqs_disabled() is true in the future. However,
theoretically, map values that get reused eagerly already have weaker
guarantees as parallel users can recreate freed fields before the new
element becomes visible again. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost/vdpa: validate virtqueue index in mmap and fault paths
vhost_vdpa_mmap() and vhost_vdpa_fault() use vma->vm_pgoff as a
virtqueue index for get_vq_notification(), but they do not validate
that the index is smaller than v->nvqs.
The ioctl path already performs both a bounds check and
array_index_nospec(), but the mmap/fault path only checks that the
index fits in u16. This allows an out-of-range queue index to reach
driver-specific get_vq_notification() callbacks.
Fix this by extracting a unified vhost_vdpa_get_vq_notification()
helper that validates the queue index against v->nvqs and applies
array_index_nospec() before calling the driver callback. Both the
mmap and fault paths use this helper, and the bounds checking is
consolidated into a single location.
From source inspection, the most defensible impact is out-of-bounds
access in the callback path, potentially leading to invalid PFN
remaps and crash/DoS. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci: validate codec capability element length
Read Local Codec Capabilities returns a sequence of capability elements.
Each element starts with a one-byte length followed by that many payload
bytes.
hci_read_codec_capabilities() checks that the skb contains the length
byte, but then validates only caps->len against the remaining skb
length. A malformed controller response with one remaining byte and
caps->len set to one passes that check even though the element needs two
bytes. The parser then records a two-byte capability and copies one
byte beyond the advertised response payload into the codec list.
Validate the full element size, including the length byte, before adding
it to the accumulated capability length. This preserves all well-formed
capability elements and drops only truncated controller responses. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Release the HW‑provided UAR index rather than the SW one
Free the UAR index returned by the hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fib_rules: Don't dump dying fib_rule in fib_rules_dump().
rocker_router_fib_event() calls fib_rule_get() during RCU dump.
If the fib_rule is dying, refcount_inc() will complain about it.
Let's call refcount_inc_not_zero() in fib_rules_dump(). |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: reject inverted service ranges from peer bindings
tipc_update_nametbl() inserts a binding advertised by a peer node using
the lower and upper service-range bounds taken directly from the wire,
without checking that lower <= upper. The local bind path validates the
ordering (tipc_uaddr_valid()), but the name-distribution path does not.
A binding with lower > upper is inserted at the far end of the
service-range rbtree (keyed on lower) where no lookup or withdrawal can
ever match it (service_range_foreach_match() requires sr->lower <= end).
The publication, its service_range node and the augmented rbtree entry
are then leaked for the lifetime of the namespace, and there is no
per-peer cap equivalent to TIPC_MAX_PUBL on locally created bindings.
Reject inverted ranges in the network path as well. A peer node can
otherwise leak unbounded binding-table memory by sending PUBLICATION
items with lower > upper. |
