| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: fix out-of-bounds write in l2cap_ecred_connect
l2cap_chan_connect() tries to ensure there are no more than
L2CAP_ECRED_CONN_SCID_MAX pending ECRED channels, so they fit in the
same L2CAP_ECRED_CONN_REQ that l2cap_ecred_connect() constructs.
However, the check only counts deferred channels. If 6 L2CAP sockets
are connected at the same time in order DDDDND (D=deferred,
N=non-deferred), the last can bump the total to max+1. It results to
one __le16 written out of bounds of the scid array, and an invalid
ECRED_CONN_REQ being sent.
Fix by leaving room for the non-deferred pending ECRED channels in the
counting in l2cap_chan_connect(), so the limit can't be exceeded.
Move counting under same critical section where the channel is added.
Although race conditions involving this appear unreachable, it's easier
to see.
Also add WARN_ON_ONCE check in l2cap_ecred_defer_connect() to make this
less brittle. |
| In the Linux kernel, the following vulnerability has been resolved:
igmp: convert struct ip_sf_list to RCU
Commit 23d2b94043ca ("igmp: Add ip_mc_list lock in ip_check_mc_rcu")
added spin_lock_bh(&im->lock) to ip_check_mc_rcu() to prevent a
use-after-free while iterating im->sources during concurrent deletions.
However, ip_check_mc_rcu() is called from RCU read-side critical
sections in packet receive and route lookup fast paths (e.g.
__mkroute_output(), ip_route_input_rcu(), and __udp4_lib_rcv()).
When igmpv3_send_cr() or igmpv3_send_report() holds &pmc->lock and
calls add_grec() -> igmpv3_newpack() -> ip_route_output_ports(),
an XFRM policy matching a multicast destination triggers
xfrm_tmpl_resolve_one() -> xfrm4_get_saddr() -> __mkroute_output() ->
ip_check_mc_rcu(). This attempts to acquire &im->lock while &pmc->lock
is already held on the same CPU, triggering a lockdep recursive locking
warning / deadlock.
Fix this by converting IPv4 struct ip_sf_list to RCU, mirroring the
IPv6 implementation in net/ipv6/mcast.c:
1. Add struct rcu_head to struct ip_sf_list and annotate sf_next,
sources, and tomb as __rcu pointers.
2. Use rcu_assign_pointer() and kfree_rcu() for list updates and
deletions.
3. Remove spin_lock_bh(&im->lock) from ip_check_mc_rcu() and traverse
im->sources locklessly with for_each_psf_rcu(), reading and writing
counter fields with READ_ONCE() and WRITE_ONCE().
Note: RCU conversion of /proc/net/mcfilter will be done in a
separate patch. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: backtracking shouldn't clear outer frame R1-R5 for callbacks
When processing calls to bpf_loop() verifier marks R1 (and R4) as
precise. R1 tracks loop iterations number and because of the
'callback_depth < R1' mechanics in check_helper_call() must be marked
precise. However, precision propagation for R1 was broken,
when bpf_loop() call was verified on a second iteration.
Consider the following verification trace:
- main: bpf_loop(nr_loops, callback ...)
- callback: BPF_EXIT
- main: bpf_loop(nr_loops, callback ...)
- ...
While the first visit of the call to bpf_loop() propagated R1
precision as expected, the second call to mark_chain_precision() in
the check_helper_call() set R1, but it was immediately reset when
backtrack_insn() processed preceding BPF_EXIT in the loop deleted in
this patch.
Because of that, the second visit of the call to bpf_loop() injected
checkpoint with R1 not marked as precise. Which could trick the
verifier into accepting unsafe programs. See the next patch for an
example of such program.
Commit is structured in a way to minimize conflicts when
'bpf' would be eventually merged with 'bpf-next'. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: remove stale namespaces by NSID range during scan
nvme_scan_ns_list() drops the stale namespaces in each gap in the
reported NSID list one NSID at a time. Every iteration calls
nvme_find_get_ns() to look the namespace up and removes it if it is
present. The loop runs once per NSID in the gap rather than once per
namespace actually present.
NSIDs are 32-bit, so a target with a sparse NSID space can make a
single gap spin the loop billions of times with nothing to remove.
watchdog: BUG: soft lockup - CPU#4 stuck for 26s!
Workqueue: nvme-wq nvme_scan_work [nvme_core]
RIP: 0010:__srcu_read_unlock+0xb/0x20
Call Trace:
nvme_find_get_ns+0x7d/0xb0 [nvme_core]
nvme_scan_ns_list+0xe8/0x280 [nvme_core]
nvme_scan_work+0x18a/0x280 [nvme_core]
process_one_work+0x197/0x380
worker_thread+0x2fe/0x410
kthread+0xe0/0x100
Rename nvme_remove_invalid_namespaces() to nvme_remove_nsid_range()
and give it an open (start, end) NSID range. ctrl->namespaces is
sorted by NSID, so the whole gap is dropped in a single walk that
stops once end is reached. This bounds the work by the namespaces
that are present instead of by the size of the gap. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Do not reallocate GA log buffers on resume
Commit c5e1a1eb9279 ("iommu/amd: Simplify and Consolidate Virtual APIC
(AVIC) Enablement") moved the GA log allocation from iommu_init_pci()
to enable_iommus_vapic(), which is called on every resume.
iommu_init_ga_log() assigns iommu->ga_log and iommu->ga_log_tail
unconditionally. Each resume therefore replaces the boot-time pointers
and leaks both old allocations. The function also uses GFP_KERNEL from a
syscore resume callback, where interrupts are disabled and the non-boot
CPUs are offline.
Return early if both buffers are already allocated. Clear the pointers
in free_ga_log() so a partial allocation failure cannot leave ga_log
dangling. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: initialize _md in vxlan_xmit_one()
If a VXLAN device is configured with both VXLAN_F_COLLECT_METADATA and
VXLAN_F_GBP, and a packet is transmitted through it using an external
ip_tunnel_info that lacks the IP_TUNNEL_VXLAN_OPT_BIT flag, md is left
pointing to the uninitialized _md stack variable:
if (test_bit(IP_TUNNEL_VXLAN_OPT_BIT, info->key.tun_flags)) {
if (info->options_len < sizeof(*md))
goto drop;
md = ip_tunnel_info_opts(info);
}
Because IP_TUNNEL_VXLAN_OPT_BIT is not set, md is not updated and remains
pointing to _md. Later, vxlan_build_skb() is called with md, which
eventually calls vxlan_build_gbp_hdr():
if (vxflags & VXLAN_F_GBP)
vxlan_build_gbp_hdr(vxh, md);
Inside vxlan_build_gbp_hdr(), md->gbp is read:
if (!md->gbp)
return;
gbp = (struct vxlanhdr_gbp *)vxh;
...
if (md->gbp & VXLAN_GBP_DONT_LEARN)
gbp->dont_learn = 1;
If the stack contains garbage, this causes:
1) VXLAN_HF_GBP flag to be spuriously set in the VXLAN header.
2) gbp->dont_learn and gbp->policy_applied to be set from stack bits.
3) gbp->policy_id to receive 16 bits of uninitialized kernel stack data,
leaking it onto the wire.
Fix this by zero-initializing _md. If IP_TUNNEL_VXLAN_OPT_BIT is not
present, md->gbp remains 0, and vxlan_build_gbp_hdr() returns early
without modifying the VXLAN header. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Prevent drain_pebs() reentry
The PEBS buffer is shared by all events on a CPU, so drain_pebs() must
not be reentered. If so, one instance may observe stale buffer state and
potentially access out-of-bound memory.
Most invocations happen in NMI context, which naturally prevents reentry.
However, drain_pebs() is also reachable from process context via
intel_pmu_drain_pebs_buffer().
In those paths, the PMU is often already disabled, but not guaranteed.
For example, __intel_pmu_pebs_disable() only disables the target counter,
so other active counters can still raise a PMI and interrupt an in-flight
drain_pebs(). Here is an example,
__perf_addr_filters_adjust()
perf_event_stop()
__perf_event_stop()
x86_pmu_stop() (event->pmu->stop)
intel_pmu_disable_event()
intel_pmu_pebs_disable()
__intel_pmu_pebs_disable()
intel_pmu_drain_large_pebs()
intel_pmu_drain_pebs_buffer()
Introduce __intel_pmu_quiesce() and __intel_pmu_resume() helpers and
use them in intel_pmu_drain_large_pebs() to disable the full PMU
around the intel_pmu_drain_pebs_buffer() call, preventing reentry.
Also add a warning in intel_pmu_drain_pebs_buffer() when the full PMU is
not disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix TX descriptor availability check for TSO traffic
stmmac_tso_xmit() estimates the number of free TX descriptors required by
a TSO skb as:
(skb->len - proto_hdr_len) / TSO_MAX_BUFF_SIZE + 1
which assumes the payload is split into TSO_MAX_BUFF_SIZE chunks. This
underestimates the descriptors actually consumed by stmmac_tso_allocator(),
since each fragment is mapped individually and so it needs at least one
descriptor regardless of its size. Moreover, one descriptor is used for
the L2/L3/L4 headers and, when the MSS changes, one more is consumed for
the MSS context descriptor.
For a highly fragmented TSO skb the check can therefore pass even when the
ring has too few free slots. stmmac_tso_allocator() then writes past the
available descriptors, overwriting descriptors still owned by the DMA
engine, corrupting the TX ring.
Add stmmac_tso_get_num_desc() to compute the exact number of descriptors
needed for the header, the linear payload and each fragment, plus the MSS
context descriptor when required, and use it in the availability check. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix memory corruption from a "STACKTRACE" histogram key
"cpu", "CPU", "stacktrace" and "STACKTRACE" are generic fields, defined
with an offset and a size of zero so that the filter code can match them
by name. parse_field() maps them onto their common_* equivalents for
backward compatibility, but unlike the common_* names it hands the
placeholder back to the caller instead of NULL.
create_hist_field() takes a non-NULL field as a promise that the record
carries a stacktrace and picks HIST_FIELD_FN_STACK, so the __data_loc
word is read from offset 0, that is from common_type, and its low 16
bits are followed as an offset into the record. What is found there
becomes the length of an unbounded memcpy. Pick an event whose id is
small enough that the offset stays inside its own record and the length
is a kernel text address:
# cd /sys/kernel/tracing
# echo 'hist:keys=STACKTRACE' > events/ftrace/print/trigger
# echo hello > trace_marker
Oops: general protection fault, probably for non-canonical address
RIP: 0010:rb_next+0x23/0x60
</IRQ>
RIP: 0010:memcpy+0xc/0x30
event_hist_trigger+0x2e7/0x12c0
Kernel panic - not syncing: Fatal exception in interrupt
Leave the field NULL, which is what the comment above the branch says
the code does and what common_stacktrace already does. FILTER_CPU and
FILTER_COMM are left alone, their create_hist_field() branches never
look at the field. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Validate full buffer range in ivpu_to_cpu_addr
Add a size parameter to ivpu_to_cpu_addr() and validate that the
whole [vpu_addr, vpu_addr + size) range stays within the BO. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Validate firmware log buffer metadata
The tracing log headers parsed by fw_log_print_buffer() reside in
DMA-shared BOs that the NPU firmware can write to.
fw_log_from_bo() validated log->header_size and log->size, but
fw_log_print_buffer() re-read those same fields from shared memory
afterwards, allowing a TOCTOU where firmware changes them between the
check and the use, and making the host dereference out-of-bounds
addresses while printing logs.
Snapshot the validated values once with READ_ONCE() and pass them down
explicitly in a new struct ivpu_fw_log_desc instead of re-reading them
from the shared struct. |
| In the Linux kernel, the following vulnerability has been resolved:
genirq/proc: Size interrupt directory names for 10-digit interrupt numbers
/proc/irq/<n>/ directory names are built in `char name[10]` buffers
with `sprintf(name, "%u", irq)`.
Ten-digit IRQ numbers already need 11 bytes including the trailing NUL, and
current sparse-IRQ configurations allow interrupt numbers in that range.
Size the temporary name buffer for the current decimal form and switch
to bounded formatting when creating or removing the proc entry. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Clean up channels on setup failure
scmi_channels_setup() can fail after the common BASE channel or earlier
protocol channels have already been registered in the TX/RX IDRs.
Route this failure through the existing channel cleanup label so the
transport channels, transport devices and IDR state created before the
failure are released before the probe error path frees the SCMI instance
ID. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Unwind TX receiver mailbox setup failure
mailbox_chan_setup() can request an additional unidirectional TX
receiver channel after successfully acquiring the primary channel. If
that second request fails, the function returns immediately and leaves
the primary channel allocated.
Unwind the primary mailbox channel before returning the error so probe
deferral or other setup failures do not leave the channel busy for later
probe attempts. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: validate RX band_idx before dereferencing phys[]
band_idx comes from a 2-bit descriptor field (0-3) and was used directly
to index dev->mt76.phys[] (size __MT_MAX_BAND == 3) and dereference the
result. A corrupt or reserved descriptor value could index out of bounds
or hit a NULL phy on parts with fewer bands. Reject invalid band indices,
mirroring mt7996_rx_get_wcid(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: do not attach hif2 WED when the main WED attach failed
If the WED attach for the primary PCIe function fails, the probe path
still attached wed_hif2 for the secondary function, leaving the device
in an inconsistent half-WED configuration that crashes later. The hif2
call also re-enabled hwrro_mode, which the failed primary attach had
just turned off.
Skip the hif2 WED setup when the primary WED device is not active. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: fix race between policy activation and blkg destruction
When switching an IO scheduler on a block device, blkcg_activate_policy()
allocates blkg_policy_data (pd) for all blkgs attached to the queue.
However, blkcg_activate_policy() may race with concurrent blkcg deletion,
leading to use-after-free and memory leak issues.
The use-after-free occurs in the following race:
T1 (blkcg_activate_policy):
- Successfully allocates pd for blkg1 (loop0->queue, blkcgA)
- Fails to allocate pd for blkg2 (loop0->queue, blkcgB)
- Enters the enomem rollback path to release blkg1 resources
T2 (blkcg deletion):
- blkcgA is deleted concurrently
- blkg1 is freed via blkg_free_workfn()
- blkg1->pd is freed
T1 (continued):
- Rollback path accesses blkg1->pd->online after pd is freed
- Triggers use-after-free
In addition, blkg_free_workfn() frees pd before removing the blkg from
q->blkg_list. This allows blkcg_activate_policy() to allocate a new pd
for a blkg that is being destroyed, leaving the newly allocated pd
unreachable when the blkg is finally freed.
Fix these races by extending blkcg_mutex coverage to serialize
blkcg_activate_policy() rollback and blkg destruction, ensuring pd
lifecycle is synchronized with blkg list visibility. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Check pointer type for all atomic RMW paths
Atomic RMW verification records an instruction pointer type only when the
current destination is PTR_TO_ARENA. A second path can therefore reach the
same instruction with an ordinary pointer without comparing it against the
saved arena type.
The post-verification fixup uses the saved type to rewrite the instruction
to BPF_PROBE_ATOMIC for every path. Record the actual destination type for
all atomic RMW paths so the existing mismatch check rejects incompatible
uses of one instruction. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nVM: Ensure INVVPID is emulated on the correct physical CPU
When emulating INVVPID, KVM executes INVVPID on the physical CPU using
vpid02 (instead of the L1 assigned VPID), after doing some validations
on the operands. However, it is possible that the physical CPU KVM
executes INVVPID on is different from the CPU L2 is running on.
For example, in the following scenario:
- L2 runs on CPU #1 and exits to L1 (vmx->nested.vmcs02.cpu=1)
- L1 migrates to CPU #2 and executes INVVPID
- KVM executes INVVPID on CPU #2
- L1 migrates back to CPU #1 and runs L2 (vmx->nested.vmcs02.cpu=1)
The TLB entries on CPU #1 are never invalidated, because INVVPID was
executed on CPU #2, and vmcs02 never ran on a different pCPU (i.e.
vmx_vcpu_load_vmcs() will *not* request KVM_REQ_TLB_FLUSH).
Ensure that INVVPID is being executed on the same pCPU that L2 last ran
on, and if not, fallback to clearing last_vpid=0 to trigger a full VPID
flush on the next nested VM-Enter (as KVM will detect L1 using a
different VPID for L2). If L2 ends up running on a different pCPU, KVM
will flush the TLB anyway through vmx_vcpu_load_vmcs(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus) Fix type confusion in notification logic
Sashiko reports:
At the start of the loop in pmbus_notify(), the code unconditionally casts
every attribute to a struct sensor_device_attribute:
drivers/hwmon/pmbus/pmbus_core.c:pmbus_notify() {
for (i = 0; i < data->num_attributes; i++) {
struct device_attribute *da = to_dev_attr(data->group.attrs[i]);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int index = attr->index;
...
}
However, data->group.attrs can contain other types like struct
pmbus_samples_reg or struct pmbus_sensor, which only embed a base
struct device_attribute.
If da is a struct pmbus_samples_reg, dev_attr is the last member. Casting
it to struct sensor_device_attribute and reading the index field appears
to access memory past the end of the allocation, which might trigger a
slab-out-of-bounds read.
Additionally, if da is a struct pmbus_sensor, casting it causes the index
field to overlap with the page, phase, and reg fields. Could this produce
a garbage mask on little-endian systems that spuriously matches the target
reg, page, and flags during an alert?
Fix the problem by using struct sensor_device_attr in struct pmbus_sensor
and struct pmbus_label. Since those attributes never trigger a
notification, set the value of attr->index to -1 for them. Use this value
to distinguish from boolean attributes which _can_ trigger a notification
and use the index field to encode mask, page, and register values. |
